[Support]: Autotracking Not Working

[brandonjones24]

Describe the problem you are having

working on implementing autotracking with my REOLINK camera. I have manual movement working via the UI, but Autotracing not so much. I am getting the following error even when disabling zoom:

WARNING : Disabling autotracking for Driveway_Zoom: FOV relative movement not supported

Version

0.13.1-34FB1C2

Frigate config file

mqtt:
  host: 192.168.0.33
  port: 1883
  user: homeassistant
  password: redacted

detectors:
  coral:
    type: edgetpu
    device: usb

logger:
  default: info
  logs:
    frigate.ptz.autotrack: debug
    frigate.ptz.onvif: debug

go2rtc:
  rtsp:
    username: admin
    password: memorial91
  streams:
    driveway_wide:
    - rtsp://admin:redacted@192.168.0.48/h264Preview_01_main
    - ffmpeg:driveway_wide#audio=aac
    driveway_wide_sub:
    - rtsp://admin:redacted@192.168.0.48/h264Preview_01_sub
    - ffmpeg:driveway_wide_sub#audio=aac
    driveway_zoom:
    - rtsp://admin:redacted@192.168.0.48/h264Preview_02_main
    - ffmpeg:driveway_zoom#audio=aac
    driveway_zoom_sub:
    - rtsp://admin:redacted@192.168.0.48/h264Preview_02_sub
    - ffmpeg:driveway_zoom_sub#audio=aac
    backyard:
    - rtsp://admin:redacted@192.168.0.17/h264Preview_01_main
    - ffmpeg:backyard#audio=aac
    backyard_sub:
    - rtsp://admin:redacted@192.168.0.17/h264Preview_01_sub
    - ffmpeg:backyard_sub#audio=aac

ffmpeg:
  hwaccel_args:
  - -hwaccel
  - qsv
  - -qsv_device
  - /dev/dri/renderD128

detect:
  # Optional: width of the frame for the input with the detect role (default: shown below)
  width: 3840
  # Optional: height of the frame for the input with the detect role (default: shown below)
  height: 2160
  # Optional: desired fps for your camera for the input with the detect role (default: shown below)
  # NOTE: Recommended value of 5. Ideally, try and reduce your FPS on the camera.
  fps: 30
  # Optional: enables detection for the camera (default: True)
  # This value can be set via MQTT and will be updated in startup based on retained value
  enabled: true
  # Optional: Number of frames without a detection before frigate considers an object to be gone. (default: 5x the frame rate)
  max_disappeared: 25
  # Optional: Configuration for stationary object tracking
  stationary:
    # Optional: Frequency for confirming stationary objects (default: shown below)
    # When set to 0, object detection will not confirm stationary objects until movement is detected.
    # If set to 10, object detection will run to confirm the object still exists on every 10th frame.
    interval: 10
    # Optional: Number of frames without a position change for an object to be considered stationary (default: 10x the frame rate or 10s)
    threshold: 50
    # Optional: Define a maximum number of frames for tracking a stationary object (default: not set, track forever)
    # This can help with false positives for objects that should only be stationary for a limited amount of time.
    # It can also be used to disable stationary object tracking. For example, you may want to set a value for person, but leave
    # car at the default.
    # WARNING: Setting these values overrides default behavior and disables stationary object tracking.
    #          There are very few situations where you would want it disabled. It is NOT recommended to
    #          copy these values from the example config into your config unless you know they are needed.
    max_frames:
      # Optional: Default for all object types (default: not set, track forever)
      default: 3000
      # Optional: Object specific values
      objects:
        person: 1000
        car: 1000
        truck: 1000

birdseye:
  # Optional: Enable birdseye view (default: shown below)
  enabled: true
  # Optional: Width of the output resolution (default: shown below)
  width: 3840
  # Optional: Height of the output resolution (default: shown below)
  height: 2160
  quality: 8
  mode: objects

objects:
  # Optional: list of objects to track from labelmap.txt (default: shown below)
  track:
  - person
  - car
  - dog
  - cat
  - bicycle
  # Optional: mask to prevent all object types from being detected in certain areas (default: no mask)
  # Checks based on the bottom center of the bounding box of the object.
  # NOTE: This mask is COMBINED with the object type specific mask below
#  mask: 0,0,1000,0,1000,200,0,200
  # Optional: filters to reduce false positives for specific object types
  filters:
    person:
      # Optional: minimum width*height of the bounding box for the detected object (default: 0)
      min_area: 5000
      # Optional: maximum width*height of the bounding box for the detected object (default: 24000000)
      max_area: 100000
      # Optional: minimum width/height of the bounding box for the detected object (default: 0)
      min_ratio: 0.5
      # Optional: maximum width/height of the bounding box for the detected object (default: 24000000)
      max_ratio: 2.0
      # Optional: minimum score for the object to initiate tracking (default: shown below)
      min_score: 0.5
      # Optional: minimum decimal percentage for tracked object's computed score to be considered a true positive (default: shown below)
      threshold: 0.7
      # Optional: mask to prevent this object type from being detected in certain areas (default: no mask)
      # Checks based on the bottom center of the bounding box of the object
 #     mask: 0,0,1000,0,1000,200,0,200
    car:
      # Optional: minimum width*height of the bounding box for the detected object (default: 0)
      min_area: 5000
      # Optional: maximum width*height of the bounding box for the detected object (default: 24000000)
      max_area: 100000
      # Optional: minimum width/height of the bounding box for the detected object (default: 0)
      min_ratio: 0.5
      # Optional: maximum width/height of the bounding box for the detected object (default: 24000000)
      max_ratio: 2.0
      # Optional: minimum score for the object to initiate tracking (default: shown below)
      min_score: 0.5
      # Optional: minimum decimal percentage for tracked object's computed score to be considered a true positive (default: shown below)
      threshold: 0.7
      # Optional: mask to prevent this object type from being detected in certain areas (default: no mask)
      # Checks based on the bottom center of the bounding box of the object
  #    mask: 0,0,1000,0,1000,200,0,200
    truck:
      # Optional: minimum width*height of the bounding box for the detected object (default: 0)
      min_area: 5000
      # Optional: maximum width*height of the bounding box for the detected object (default: 24000000)
      max_area: 100000
      # Optional: minimum width/height of the bounding box for the detected object (default: 0)
      min_ratio: 0.5
      # Optional: maximum width/height of the bounding box for the detected object (default: 24000000)
      max_ratio: 2.0
      # Optional: minimum score for the object to initiate tracking (default: shown below)
      min_score: 0.5
      # Optional: minimum decimal percentage for tracked object's computed score to be considered a true positive (default: shown below)
      threshold: 0.7
      # Optional: mask to prevent this object type from being detected in certain areas (default: no mask)
      # Checks based on the bottom center of the bounding box of the object
#      mask: 0,0,1000,0,1000,200,0,200
# Optional: Motion configuration
# NOTE: Can be overridden at the camera level
motion:
  # Optional: The threshold passed to cv2.threshold to determine if a pixel is different enough to be counted as motion. (default: shown below)
  # Increasing this value will make motion detection less sensitive and decreasing it will make motion detection more sensitive.
  # The value should be between 1 and 255.
  threshold: 15
  # Optional: Minimum size in pixels in the resized motion image that counts as motion (default: 30)
  # Increasing this value will prevent smaller areas of motion from being detected. Decreasing will
  # make motion detection more sensitive to smaller moving objects.
  # As a rule of thumb:
  #  - 15 - high sensitivity
  #  - 30 - medium sensitivity
  #  - 50 - low sensitivity
  contour_area: 30
  # Optional: Alpha value passed to cv2.accumulateWeighted when averaging the motion delta across multiple frames (default: shown below)
  # Higher values mean the current frame impacts the delta a lot, and a single raindrop may register as motion.
  # Too low and a fast moving person wont be detected as motion.
  delta_alpha: 0.2
  # Optional: Alpha value passed to cv2.accumulateWeighted when averaging frames to determine the background (default: shown below)
  # Higher values mean the current frame impacts the average a lot, and a new object will be averaged into the background faster.
  # Low values will cause things like moving shadows to be detected as motion for longer.
  # https://www.geeksforgeeks.org/background-subtraction-in-an-image-using-concept-of-running-average/
  frame_alpha: 0.2
  # Optional: Height of the resized motion frame  (default: 50)
  # This operates as an efficient blur alternative. Higher values will result in more granular motion detection at the expense
  # of higher CPU usage. Lower values result in less CPU, but small changes may not register as motion.
  frame_height: 50
  # Optional: motion mask
  # NOTE: see docs for more detailed info on creating masks
 # mask: 0,900,1080,900,1080,1920,0,1920
  # Optional: improve contrast (default: shown below)
  # Enables dynamic contrast improvement. This should help improve night detections at the cost of making motion detection more sensitive
  # for daytime.
  improve_contrast: false
  # Optional: Delay when updating camera motion through MQTT from ON -> OFF (default: shown below).
  mqtt_off_delay: 30

# Optional: Record configuration
# NOTE: Can be overridden at the camera level
record:
  # Optional: Enable recording (default: shown below)
  # WARNING: If recording is disabled in the config, turning it on via
  #          the UI or MQTT later will have no effect.
  # WARNING: Frigate does not currently support limiting recordings based
  #          on available disk space automatically. If using recordings,
  #          you must specify retention settings for a number of days that
  #          will fit within the available disk space of your drive or Frigate
  #          will crash.
  enabled: true
  # Optional: Number of minutes to wait between cleanup runs (default: shown below)
  # This can be used to reduce the frequency of deleting recording segments from disk if you want to minimize i/o
  expire_interval: 60
  # Optional: Retention settings for recording
  retain:
    # Optional: Number of days to retain recordings regardless of events (default: shown below)
    # NOTE: This should be set to 0 and retention should be defined in events section below
    #       if you only want to retain recordings of events.
    days: 30
    # Optional: Mode for retention. Available options are: all, motion, and active_objects
    #   all - save all recording segments regardless of activity
    #   motion - save all recordings segments with any detected motion
    #   active_objects - save all recording segments with active/moving objects
    # NOTE: this mode only applies when the days setting above is greater than 0
    mode: all
  # Optional: Event recording settings
  events:
    # Optional: Number of seconds before the event to include (default: shown below)
    pre_capture: 2
    # Optional: Number of seconds after the event to include (default: shown below)
    post_capture: 5
    # Optional: Objects to save recordings for. (default: all tracked objects)
    objects:
    - person
    - car
    - dog
    - cat
    - bicycle
    - ups
    - fedex
    # Optional: Restrict recordings to objects that entered any of the listed zones (default: no required zones)
    required_zones: []
    # Optional: Retention settings for recordings of events
    retain:
      # Required: Default retention days (default: shown below)
      default: 10
      # Optional: Mode for retention. (default: shown below)
      #   all - save all recording segments for events regardless of activity
      #   motion - save all recordings segments for events with any detected motion
      #   active_objects - save all recording segments for event with active/moving objects
      #
      # NOTE: If the retain mode for the camera is more restrictive than the mode configured
      #       here, the segments will already be gone by the time this mode is applied.
      #       For example, if the camera retain mode is "motion", the segments without motion are
      #       never stored, so setting the mode to "all" here won't bring them back.
      mode: all
      # Optional: Per object retention days
      objects:
        person: 30
        car: 15
        truck: 15
        dog: 15
        cat: 5
        bird: 5
        horse: 5
        hat: 5
        backpack: 5
        umbrella: 5
        baseball bat: 30
        skateboard: 30
        knife: 10
        ups: 5
        fedex: 5

# Optional: Configuration for the jpg snapshots written to the clips directory for each event
# NOTE: Can be overridden at the camera level
snapshots:
  # Optional: Enable writing jpg snapshot to /media/frigate/clips (default: shown below)
  # This value can be set via MQTT and will be updated in startup based on retained value
  enabled: true
  # Optional: save a clean PNG copy of the snapshot image (default: shown below)
  clean_copy: true
  # Optional: print a timestamp on the snapshots (default: shown below)
  timestamp: false
  # Optional: draw bounding box on the snapshots (default: shown below)
  bounding_box: false
  # Optional: crop the snapshot (default: shown below)
  crop: false
  # Optional: height to resize the snapshot to (default: original size)
  height: 2160
  # Optional: Restrict snapshots to objects that entered any of the listed zones (default: no required zones)
  required_zones: []
  # Optional: Camera override for retention settings (default: global values)
  retain:
    # Required: Default retention days (default: shown below)
    default: 30
    # Optional: Per object retention days
    objects:
      person: 30

cameras:
  Driveway_wide:
    ffmpeg:
      output_args:
        record: -f segment -segment_time 10 -segment_format mp4 -reset_timestamps
          1 -strftime 1 -c:v copy -tag:v hvc1 -bsf:v hevc_mp4toannexb -c:a aac
        rtmp: -c:v copy -c:a aac -f flv
      inputs:
      - path: rtsp://127.0.0.1:8554/driveway_wide?video=copy&audio=aac   # <--- the name here must match the name of the camera in restream
        input_args: preset-rtsp-restream
        roles:
        - record
      - path: rtsp://127.0.0.1:8554/driveway_wide_sub?video=copy&audio=aac   # <--- the name here must match the name of the camera_sub in restream
        input_args: preset-rtsp-restream
        roles:
        - detect


  Driveway_Zoom:
    ffmpeg:
      output_args:
        record: -f segment -segment_time 10 -segment_format mp4 -reset_timestamps
          1 -strftime 1 -c:v copy -tag:v hvc1 -bsf:v hevc_mp4toannexb -c:a aac
        rtmp: -c:v copy -c:a aac -f flv
      inputs:
      - path: rtsp://127.0.0.1:8554/driveway_zoom?video=copy&audio=aac   # <--- the name here must match the name of the camera in restream
        input_args: preset-rtsp-restream
        roles:
        - record
      - path: rtsp://127.0.0.1:8554/driveway_zoom_sub?video=copy&audio=aac   # <--- the name here must match the name of the camera_sub in restream
        input_args: preset-rtsp-restream
        roles:
        - detect
    zones:
      driveway:
        coordinates: 1280,325,1280,720,0,720,0,435
      road:
        coordinates: 0,300,300,176,856,147,1280,226,1280,229,1280,289,565,312,340,338,0,381

    onvif:
      # Required: host of the camera being connected to.
      host: 192.168.0.48
      # Optional: ONVIF port for device (default: shown below).
      port: 8000
      # Optional: username for login.
      # NOTE: Some devices require admin to access ONVIF.
      user: admin
      # Optional: password for login.
      password: redacted
      # Optional: PTZ camera object autotracking. Keeps a moving object in
      # the center of the frame by automatically moving the PTZ camera.
      autotracking:
        # Optional: enable/disable object autotracking. (default: shown below)
        enabled: True
        # Optional: calibrate the camera on startup (default: shown below)
        # A calibration will move the PTZ in increments and measure the time it takes to move.
        # The results are used to help estimate the position of tracked objects after a camera move.
        # Frigate will update your config file automatically after a calibration with
        # a "movement_weights" entry for the camera. You should then set calibrate_on_startup to False.
        calibrate_on_startup: True
        # Optional: the mode to use for zooming in/out on objects during autotracking. (default: shown below)
        # Available options are: disabled, absolute, and relative
        #   disabled - don't zoom in/out on autotracked objects, use pan/tilt only
        #   absolute - use absolute zooming (supported by most PTZ capable cameras)
        #   relative - use relative zooming (not supported on all PTZs, but makes concurrent pan/tilt/zoom movements)
        # zooming: absolute
        # Optional: A value to change the behavior of zooming on autotracked objects. (default: shown below)
        # A lower value will keep more of the scene in view around a tracked object.
        # A higher value will zoom in more on a tracked object, but Frigate may lose tracking more quickly.
        # The value should be between 0.1 and 0.75
        zoom_factor: 0.3
        # Optional: list of objects to track from labelmap.txt (default: shown below)
        track:
          - person
          - dog
          - car
        # Required: Begin automatically tracking an object when it enters any of the listed zones.
        required_zones:
          - driveway
          - road
        # Required: Name of ONVIF preset in camera's firmware to return to when tracking is over. (default: shown below)
        return_preset: home
        # Optional: Seconds to delay before returning to preset. (default: shown below)
        timeout: 10
        # Optional: Values generated automatically by a camera calibration. Do not modify these manually. (default: shown below)
        # movement_weights: []

  Backyard:
    ffmpeg:
      output_args:
        record: -f segment -segment_time 10 -segment_format mp4 -reset_timestamps
          1 -strftime 1 -c:v copy -tag:v hvc1 -bsf:v hevc_mp4toannexb -c:a aac
        rtmp: -c:v copy -c:a aac -f flv
      inputs:
      - path: rtsp://127.0.0.1:8554/backyard?video=copy&audio=aac   # <--- the name here must match the name of the camera in restream
        input_args: preset-rtsp-restream
        roles:
        - record
      - path: rtsp://127.0.0.1:8554/backyard_sub?video=copy&audio=aac   # <--- the name here must match the name of the camera_sub in restream
        input_args: preset-rtsp-restream
        roles:
        - detect
#  porch:
#    ffmpeg:
#      output_args:
#        record: -f segment -segment_time 10 -segment_format mp4 -reset_timestamps 1 -strftime 1 -c:v copy -tag:v hvc1 -bsf:v hevc_mp4toannexb -c:a aac
#        rtmp: -c:v copy -c:a aac -f flv
#      inputs:
#        - path: rtsp://192.168.0.12:8554/side-porch-cam # <--- the name here must match the name of the camera in restream
#          input_args: preset-rtsp-restream
#          roles:
#            - record
#            - detect

Relevant log output

2024-02-20 23:40:21.188535277  [2024-02-20 23:40:18] frigate.ptz.autotrack          DEBUG   : Driveway_Zoom: Autotracker init
2024-02-20 23:40:21.194933889  [2024-02-20 23:40:18] frigate.detectors.plugins.edgetpu_tfl INFO    : Attempting to load TPU as usb
2024-02-20 23:40:21.195067450  [2024-02-20 23:40:18] frigate.ptz.onvif              DEBUG   : Onvif configs for Driveway_Zoom: {
2024-02-20 23:40:21.195068940      'Name': 'PtzConfig000',
2024-02-20 23:40:21.195069773      'UseCount': 3,
2024-02-20 23:40:21.195070569      'NodeToken': '000',
2024-02-20 23:40:21.195074578      'DefaultAbsolutePantTiltPositionSpace': None,
2024-02-20 23:40:21.195075519      'DefaultAbsoluteZoomPositionSpace': None,
2024-02-20 23:40:21.195087417      'DefaultRelativePanTiltTranslationSpace': None,
2024-02-20 23:40:21.195088350      'DefaultRelativeZoomTranslationSpace': None,
2024-02-20 23:40:21.195089721      'DefaultContinuousPanTiltVelocitySpace': 'http://www.onvif.org/ver10/tptz/PanTiltSpaces/VelocityGenericSpace',
2024-02-20 23:40:21.195090572      'DefaultContinuousZoomVelocitySpace': 'http://www.onvif.org/ver10/tptz/ZoomSpaces/VelocityGenericSpace',
2024-02-20 23:40:21.195106046      'DefaultPTZSpeed': {
2024-02-20 23:40:21.195106881          'PanTilt': {
2024-02-20 23:40:21.195107594              'x': 1.0,
2024-02-20 23:40:21.195108283              'y': 1.0,
2024-02-20 23:40:21.195109104              'space': 'http://www.onvif.org/ver10/tptz/PanTiltSpaces/GenericSpeedSpace'
2024-02-20 23:40:21.195117907          },
2024-02-20 23:40:21.195118552          'Zoom': {
2024-02-20 23:40:21.195119186              'x': 1.0,
2024-02-20 23:40:21.195119976              'space': 'http://www.onvif.org/ver10/tptz/ZoomSpaces/ZoomGenericSpeedSpace'
2024-02-20 23:40:21.195120653          }
2024-02-20 23:40:21.195121338      },
2024-02-20 23:40:21.195122023      'DefaultPTZTimeout': datetime.timedelta(seconds=5),
2024-02-20 23:40:21.195122657      'PanTiltLimits': {
2024-02-20 23:40:21.195123342          'Range': {
2024-02-20 23:40:21.195124171              'URI': 'http://www.onvif.org/ver10/tptz/PanTiltSpaces/PositionGenericSpace',
2024-02-20 23:40:21.195124813              'XRange': {
2024-02-20 23:40:21.195133251                  'Min': -1.0,
2024-02-20 23:40:21.195133922                  'Max': 1.0
2024-02-20 23:40:21.195134489              },
2024-02-20 23:40:21.195135178              'YRange': {
2024-02-20 23:40:21.195135810                  'Min': -1.0,
2024-02-20 23:40:21.195136549                  'Max': 1.0
2024-02-20 23:40:21.195137211              }
2024-02-20 23:40:21.195137772          }
2024-02-20 23:40:21.195138390      },
2024-02-20 23:40:21.195139080      'ZoomLimits': {
2024-02-20 23:40:21.195139690          'Range': {
2024-02-20 23:40:21.195140407              'URI': 'http://www.onvif.org/ver10/tptz/ZoomSpaces/PositionGenericSpace',
2024-02-20 23:40:21.195149553              'XRange': {
2024-02-20 23:40:21.195150205                  'Min': -1.0,
2024-02-20 23:40:21.195150825                  'Max': 1.0
2024-02-20 23:40:21.195151412              }
2024-02-20 23:40:21.195151970          }
2024-02-20 23:40:21.195152560      },
2024-02-20 23:40:21.195153162      'Extension': None,
2024-02-20 23:40:21.195153867      'token': '000',
2024-02-20 23:40:21.195154441      '_attr_1': {
2024-02-20 23:40:21.195155023  }
2024-02-20 23:40:21.195155579  }
2024-02-20 23:40:21.195156335  [2024-02-20 23:40:21] frigate.detectors.plugins.edgetpu_tfl INFO    : TPU found
2024-02-20 23:40:21.195429058  [2024-02-20 23:40:18] frigate.ptz.onvif              DEBUG   : Onvif config for Driveway_Zoom: {
2024-02-20 23:40:21.195430273      'Spaces': {
2024-02-20 23:40:21.195430925          'AbsolutePanTiltPositionSpace': [],
2024-02-20 23:40:21.195431576          'AbsoluteZoomPositionSpace': [],
2024-02-20 23:40:21.195432245          'RelativePanTiltTranslationSpace': [],
2024-02-20 23:40:21.195433038          'RelativeZoomTranslationSpace': [],
2024-02-20 23:40:21.195433750          'ContinuousPanTiltVelocitySpace': [
2024-02-20 23:40:21.195434443              {
2024-02-20 23:40:21.195435248                  'URI': 'http://www.onvif.org/ver10/tptz/PanTiltSpaces/VelocityGenericSpace',
2024-02-20 23:40:21.195435844                  'XRange': {
2024-02-20 23:40:21.195436390                      'Min': -1.0,
2024-02-20 23:40:21.195437025                      'Max': 1.0
2024-02-20 23:40:21.195437600                  },
2024-02-20 23:40:21.195438169                  'YRange': {
2024-02-20 23:40:21.195438844                      'Min': -1.0,
2024-02-20 23:40:21.195439497                      'Max': 1.0
2024-02-20 23:40:21.195440125                  }
2024-02-20 23:40:21.195440719              }
2024-02-20 23:40:21.195441291          ],
2024-02-20 23:40:21.195441974          'ContinuousZoomVelocitySpace': [
2024-02-20 23:40:21.195442598              {
2024-02-20 23:40:21.195443408                  'URI': 'http://www.onvif.org/ver10/tptz/ZoomSpaces/VelocityGenericSpace',
2024-02-20 23:40:21.195443971                  'XRange': {
2024-02-20 23:40:21.195444611                      'Min': -1.0,
2024-02-20 23:40:21.195445239                      'Max': 1.0
2024-02-20 23:40:21.195445799                  }
2024-02-20 23:40:21.195446404              }
2024-02-20 23:40:21.195447018          ],
2024-02-20 23:40:21.195447649          'PanTiltSpeedSpace': [
2024-02-20 23:40:21.195448240              {
2024-02-20 23:40:21.195449042                  'URI': 'http://www.onvif.org/ver10/tptz/PanTiltSpaces/GenericSpeedSpace',
2024-02-20 23:40:21.195449675                  'XRange': {
2024-02-20 23:40:21.195450302                      'Min': 0.0,
2024-02-20 23:40:21.195450874                      'Max': 1.0
2024-02-20 23:40:21.195451434                  }
2024-02-20 23:40:21.195452005              }
2024-02-20 23:40:21.195452548          ],
2024-02-20 23:40:21.195453204          'ZoomSpeedSpace': [
2024-02-20 23:40:21.195453848              {
2024-02-20 23:40:21.195454613                  'URI': 'http://www.onvif.org/ver10/tptz/ZoomSpaces/ZoomGenericSpeedSpace',
2024-02-20 23:40:21.195455273                  'XRange': {
2024-02-20 23:40:21.195455870                      'Min': -1.0,
2024-02-20 23:40:21.195456424                      'Max': 1.0
2024-02-20 23:40:21.195457017                  }
2024-02-20 23:40:21.195457591              }
2024-02-20 23:40:21.195458180          ],
2024-02-20 23:40:21.195458763          'Extension': None,
2024-02-20 23:40:21.195459397          '_attr_1': None
2024-02-20 23:40:21.195459997      },
2024-02-20 23:40:21.195460593      'PTZTimeout': {
2024-02-20 23:40:21.195461179          'Min': datetime.timedelta(seconds=1),
2024-02-20 23:40:21.195461857          'Max': datetime.timedelta(seconds=10)
2024-02-20 23:40:21.195462393      },
2024-02-20 23:40:21.195463015      '_value_1': None,
2024-02-20 23:40:21.195463924      'PTControlDirection': None,
2024-02-20 23:40:21.195464487      'Extension': None,
2024-02-20 23:40:21.195465110      '_attr_1': None
2024-02-20 23:40:21.195465653  }
2024-02-20 23:40:21.195466391  [2024-02-20 23:40:18] frigate.ptz.onvif              DEBUG   : Onvif status config for Driveway_Zoom: {
2024-02-20 23:40:21.195466933      'Position': None,
2024-02-20 23:40:21.195467457      'MoveStatus': {
2024-02-20 23:40:21.195483010          'PanTilt': 'IDLE',
2024-02-20 23:40:21.195483637          'Zoom': 'IDLE'
2024-02-20 23:40:21.195484239      },
2024-02-20 23:40:21.195484846      'Error': None,
2024-02-20 23:40:21.195485542      'UtcTime': datetime.datetime(2024, 2, 20, 23, 40, 5, tzinfo=<isodate.tzinfo.Utc object at 0x7f9eaaaf1820>),
2024-02-20 23:40:21.195486073      '_value_1': None,
2024-02-20 23:40:21.195486648      '_attr_1': None
2024-02-20 23:40:21.195487166  }
2024-02-20 23:40:21.195487946  [2024-02-20 23:40:18] frigate.ptz.onvif              DEBUG   : Driveway_Zoom: Relative move request: {
2024-02-20 23:40:21.195488616      'ProfileToken': '000',
2024-02-20 23:40:21.195489287      'Translation': None,
2024-02-20 23:40:21.195489918      'Speed': None
2024-02-20 23:40:21.195490406  }
2024-02-20 23:40:21.195491291  [2024-02-20 23:40:18] frigate.ptz.onvif              DEBUG   : Driveway_Zoom: Relative move request after setup: {
2024-02-20 23:40:21.195491874      'ProfileToken': '000',
2024-02-20 23:40:21.195492473      'Translation': None,
2024-02-20 23:40:21.195493057      'Speed': {
2024-02-20 23:40:21.195493642          'PanTilt': {
2024-02-20 23:40:21.195494225              'x': 1.0,
2024-02-20 23:40:21.195506672              'y': 1.0,
2024-02-20 23:40:21.195507511              'space': 'http://www.onvif.org/ver10/tptz/PanTiltSpaces/GenericSpeedSpace'
2024-02-20 23:40:21.195508110          },
2024-02-20 23:40:21.195508630          'Zoom': {
2024-02-20 23:40:21.195509254              'x': 1.0,
2024-02-20 23:40:21.195510114              'space': 'http://www.onvif.org/ver10/tptz/ZoomSpaces/ZoomGenericSpeedSpace'
2024-02-20 23:40:21.195510685          }
2024-02-20 23:40:21.195511353      }
2024-02-20 23:40:21.195511962  }
2024-02-20 23:40:21.195513241  [2024-02-20 23:40:18] frigate.ptz.autotrack          WARNING : Disabling autotracking for Driveway_Zoom: FOV relative movement not supported

FFprobe output from your camera

ffprobe version 5.1.2 Copyright (c) 2007-2022 the FFmpeg developers
  built with Apple clang version 14.0.0 (clang-1400.0.29.202)
  configuration: --prefix=/opt/homebrew/Cellar/ffmpeg/5.1.2_4 --enable-shared --enable-pthreads --enable-version3 --cc=clang --host-cflags= --host-ldflags= --enable-ffplay --enable-gnutls --enable-gpl --enable-libaom --enable-libaribb24 --enable-libbluray --enable-libdav1d --enable-libmp3lame --enable-libopus --enable-librav1e --enable-librist --enable-librubberband --enable-libsnappy --enable-libsrt --enable-libsvtav1 --enable-libtesseract --enable-libtheora --enable-libvidstab --enable-libvmaf --enable-libvorbis --enable-libvpx --enable-libwebp --enable-libx264 --enable-libx265 --enable-libxml2 --enable-libxvid --enable-lzma --enable-libfontconfig --enable-libfreetype --enable-frei0r --enable-libass --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-libopenjpeg --enable-libspeex --enable-libsoxr --enable-libzmq --enable-libzimg --disable-libjack --disable-indev=jack --enable-videotoolbox --enable-neon
  libavutil      57. 28.100 / 57. 28.100
  libavcodec     59. 37.100 / 59. 37.100
  libavformat    59. 27.100 / 59. 27.100
  libavdevice    59.  7.100 / 59.  7.100
  libavfilter     8. 44.100 /  8. 44.100
  libswscale      6.  7.100 /  6.  7.100
  libswresample   4.  7.100 /  4.  7.100
  libpostproc    56.  6.100 / 56.  6.100
Input #0, rtsp, from 'rtsp://admin:redacted@192.168.0.48/h264Preview_01_main':
  Metadata:
    title           : Session streamed by "preview"
    comment         : h264Preview_01_main
  Duration: N/A, start: 0.000063, bitrate: N/A
  Stream #0:0: Video: hevc (Main), yuv420p(tv), 3840x2160, 25 fps, 25 tbr, 90k tbn
  Stream #0:1: Audio: aac (LC), 16000 Hz, mono, fltp

Frigate stats

No response

Operating system

Other Linux

Install method

Docker Compose

Coral version

USB

Network connection

Wired

Camera make and model

Reolink TrackMix PoE

Any other information that may be helpful

No response

[NickM-27]

Like it says in the docs, reolink cameras do not support the necessary features to use autotracking

[KurtBelyeu]

any chance this will work in the future?

[hawkeye217]

The only way it would ever work in the future is if Reolink updates their firmware to support more of the ONVIF standard.